Deutz

GRANIT Control unit
Technical data:
max. operating pressure: 220 bar
nominal flow rate: max. 40l/min.
tightening torque: 25 Nm
dimensions: 220 x Ø 57.9 mm
GRANIT Control unit
Technical data:
max. operating pressure: 220 bar
nominal flow rate: max. 40l/min.
tightening torque: 25 Nm
dimensions: 220 x Ø 57.9 mm
GRANIT Control unit
Technical data:
max. operating pressure: 220 bar
nominal flow: max. 40l/min.
tightening torque: 25 Nm
dimensions: 220 x Ø 58 mm
GRANIT Control unit

GRANIT Control unit

Can be switched between single- and double-acting, with float position and limit stop

Part no.:85219008
Technical data:
Max. operating pressure: 220 bar
Nominal flow rate: max. 70 l/min
Tightening torque: 30 Nm
Connections: M22 x 1.5
Dimensions: 275 x 40 x 110 mm
Description:
This auxiliary control unit is a four-position device that can be used for double- and single-acting lifting cylinders. It has gate-sealed cylinder connections A and B. This means extremely low leakage rates is permissible at high loads. The device has a detent position in the lifting position that is equipped with an automatic hydraulic limit switch, and that releases at 180 bar. When switching via the lowering position, the locked float position is engaged. This cannot be unlocked hydraulically (consumer connections A and B are connected to the return line). The float position can be used on double- and single-acting lifting cylinders as locked lowering position. The auxiliary control unit can be switched from double- to single-acting and vice versa. This is also possible during operation. The valve can be mounted on the left or right side using a freely positionable sealing plate.
GRANIT Control unit
Technical data:
max. operating pressure: 220 bar
nominal flow: max. 40l/min.
tightening torque: 25 Nm
dimensions: 220 x Ø 57.9 mm
Description:
The control valve is used in the tractor to control and regulate the power lift. Using the control valve, implements mounted on the hoist can be continuously raised and lowered, a predetermined position can be maintained, or optimal utilisation of tractor power can be achieved. Disturbances are constantly corrected automatically, making it much easier to drive the tractor. The control valve can be used for storage control, traction control or mixed control depending on the application.
GRANIT End plate

GRANIT End plate

For SD60 economical
This end plate is necessary to close a valve section with the control valve

Part no.:85219036
Technical data:
max. operating pressure: 250 bar
nominal flow: max. 50l/min
tightening torque: 30 Nm
dimensions: 100 x 118 x 25 mm
fixing: 3x M8
GRANIT Control unit

GRANIT Control unit

This control valve is used in the tractor for controlling the power lift unit. It can also be used to lift and lower implements continuously, to maintain a predetermined position, or to achieve optimum utilisation of the tractor power. Disturbances are adjusted automatically which makes driving easier. The control valve can be used for position control, traction control or mixed control depending on the application.

Part no.:85222000
Technical data:
max. operating pressure: 220 bar
nominal flow rate: max. 40l/min.
tightening torque: 25 Nm
dimensions: 220 x Ø 57.9 mm
GRANIT Control unit
Technical data:
max. operating pressure: 220 bar
nominal flow: max. 40l/min.
tightening torque: 25 Nm
dimensions: 220 x Ø 58 mm
GRANIT Control unit

GRANIT Control unit

This auxiliary control unit is a four-position device that can be used for double- and single-acting lifting cylinders. It has gate-sealed consumer connections A and B. This means extremely low internal leakage rates under high loads. The consumer connections A and B can be found on the top and bottom of the housing. The device has a detent position in the lifting position that is equipped with an automatic hydraulic limit switch, and that releases at 180 bar. When switching via the lowering position, the locked float position is engaged. This cannot be unlocked hydraulically (consumer connections A and B are connected to the return line). The float position can be used on double- and single-acting lifting cylinders as locked lowering position. The auxiliary control unit can be switched from double- to single-acting and vice versa. This is also possible during operation.

Part no.:85219009
Technical data:
Max. operating pressure: 220 bar
Nominal flow rate: max. 60l/min
Tightening torque: 30 Nm
Connections: M18 x 1.5
dimensions: 130 x 220 x 50 mm
GRANIT Control unit

GRANIT Control unit

Can be switched between single- and double-acting, with float position with 3x detent (lift, lower, float position) and limit stop (with lever)

Part no.:85219010
Technical data:
Max. operating pressure: 220 bar
Nominal flow rate: max. 60 l/min
Tightening torque: 30 Nm
Connections: M18 x 1.5
Dimensions: 230 x 120 x 50 mm
Description:
This control valve has been specially developed for Deutz tractors with SD60 hydraulics. Thanks to the high output up to four pieces can be flanged directly. As the hole pattern is identical to Deutz, this valve can also be mixed with Deutz SD-60 valves. The aforementioned control valve is a four-position valve, and can be switched via handwheel from double-acting to single-acting and vice versa. It is a gate-sealed control valve with neutral fine control that allows very low fit leakage, even at the highest pressure. The device has a latched safety limit switch in the lifting position. When switching via the lowering position, the latched float position is reached. This can be returned by hand to the neutral position at any time.
GRANIT Control unit
Technical data:
max. operating pressure: 210 bar
nominal flow: min. 90 l/min.
operating material: hydraulic oil
tightening torque: 30 Nm
connections: M22 x 1.5
dimensions: 260 x 40 x 150 mm
Description:
This auxiliary control unit is a 5/4-way valve which is manually operated to control cylinders and hydraulic motors. The auxiliary control unit is a four-position control unit that can be used for double- and single-acting lifting cylinders. It has O-ring-sealed cylinder connections A and B. This means that there is no leakage at high loads. The device has a detent position in the lifting position which is equipped with an automatic hydraulic limit switch, and unlocked at 180 bar. When switching via the lowering position, the locked float position is turned on. This is not hydraulically unlocked (consumer connections A and B are connected to the return). The float position can be used as a latched lowering position for double-acting and single-acting lifting cylinders. The valve can be mounted by a freely positionable sealing plate on the left or right side. The sealing plate is included in delivery.
GRANIT replacement parts are not intended to be sold as OEM parts. OEM part numbers are provided for reference purposes only. All prices are in €, excl. VAT. Errors reserved. Delivery subject to availability.