Ilgenfritz control unit

Ilgenfritz Hoist signal electronics assembly

Ilgenfritz Hoist signal electronics assembly

For retrofitting the lifting unit signal to the 7-pin signal socket
Set of parts with installation accessories

Part no.:506002026
Version:
For retrofitting the lifting unit signal to the 7-pin signal socket
Set of parts with installation accessories
To fit as:
John Deere tractors
Included in delivery:
Module, cable, accessories, manual
Technical data:
The linkage signal electronics provides the linkage signal of the 7-pin signal socket without the installation of an additional sensor on the linkage.
The original angle sensor of the power lift is used to determine the lift height.
The angle at which the electronics switches the linkage signal is configurable and can thus be adapted to your needs.
The switched linkage signal has a level of 12V.
This signal is required, for example, for slug pellet spreaders, seed drills, seed spreaders, etc.

All advantages at a glance:
- Simple retrofitting of the lifting signal via the original lifting sensor (0.5 V sensor signal)
- The switching time can be set using the learning function or software
- The contact pin for the 7-pin signal socket is mounted on the cable harness
- Fast, cost-effective installation
- Illustrated installation instructions
Show more details
Ilgenfritz Hydraulic remote control CAN

Ilgenfritz Hydraulic remote control CAN

Set of parts with installation accessories

Part no.:506002003
Version:
For retrofitting, set of parts with installation accessories
To fit as:
John Deere 6R (MY2015) round button
Included in delivery:
Module, cable, accessories, manual
Technical data:
Practical examples: • You wish to connect a machine to the three-point front hydraulics and must move the lower links to do so. • You wish to connect a machine to the front or rear hydraulics and must make the hydraulic top link longer or shorter to do so. • You wish to fill a slurry tanker with a hydraulically driven pump from the mudguard without having to climb onto the tractor again. What we do: We have developed an electronic system which allows external operation via two push buttons similar to that possible with the hydraulics remote control. This electronic system is technically different from the previous solution. The biggest advantage is that the system receives oil level information from the control unit via a learning function, and not via a potentiometer (as was the case previously). The driver of the machine can therefore find out the oil level at any time. In addition, the set oil level at the control unit is always given, regardless of how high the level in the cab is set in the DTI or BIF. The installation time is also substantially reduced as the system is installed with original plugs outside the cab directly at the control units. Installation of the electronic system takes approx. 0.5 - 1.0 hour.
Show more details
Ilgenfritz four-wheel drive control

Ilgenfritz four-wheel drive control

With activation button
Set of parts with installation accessories

Part no.:506002023
Version:
With activation button
Set of parts with installation accessories
To fit as:
John Deere 6M, 6MC, 6R, 6RC, 7R (MY 11), 8R (MY 14)
Included in delivery:
Module, cable, accessories, manual
Technical data:
The electronic system prevents four-wheel drive tensioning during braking by disengaging the four-wheel drive below a desired speed. By disengaging the four-wheel drive while the vehicle is rolling, the tension in the vehicle is released without jolts. The four-wheel drive disengagement speed is set to 6 km/h as standard, and the engagement speed is set to 7 km/h. This function is only active when the four-wheel drive is deactivated. If you wish to set a different engagement/disengagement speed, please specify these when ordering. This function is only active when the four-wheel drive is deactivated, and must be activated after the ignition is switched on using the push button supplied. An integrated control light shows the activation status. If you wish to set a different engagement/disengagement speed, please specify these when ordering.
Show more details
Ilgenfritz Analogue speed control
Version:
Complete installation kit
To fit as:
John Deere 5020, 5M, 5R, 6020, 6030, 6M, 6MC, 6RC tractors
Included in delivery:
Module, cable, accessories, manual
Technical data:
The module is easily inserted in the original cable harness, and the additional switch is plugged into the switch field. Installation only takes 10 minutes and can be carried out by non-professional users.
Show more details
Ilgenfritz External PTO shaft remote control

Ilgenfritz External PTO shaft remote control

For John Deere tractors, for remotely controlling power take-off without previous activation
With electronic PTO shaft activation. Set of parts with 2 power take-off buttons and installation accessories

Part no.:506002033
Version:
For John Deere tractors, for remotely controlling power take-off without previous activation
With electronic PTO shaft activation. Set of parts with 2 power take-off buttons and installation accessories
To fit as:
John Deere 5620-5820, 5070M-5100M, 5080R-5100R, 6000-6910, 6120-6920S, 6130-6930 & 7430-7530, 6115M-6170M, 6090MC-6110MC, 6105R-6215R, 6090RC-6110RC tractors
Included in delivery:
Module, cable, accessories, manual
Technical data:
When using for the first time, external power take-off activation must be carried out via switch or the tractor’s internal control unit before it can be activated externally. This type of activation is laborious and time-consuming. The Ilgenfritz Electronics remote power take-off control allows you to comfortably activate and deactivate the rear power take-off using the external button. To activate, just press and hold the button for 5 seconds and the power take-off will initiate and the control LED on the button will light up. Press the button again to deactivate the power take-off. The internally activated power take-off can also be deactivated by pressing the button. The Ilgenfritz Electronics team value your safety, and have used high-quality, monitored buttons and a completely waterproof electronic system. Unlike their competitors who have not put as much work into power take-off activation safety, this electronic system detects all button states - even disconnected or short-circuited buttons. In addition, you can keep your original John Deere activation button in the cab rather than replacing it with an inexpensive replica.
Show more details
Original spare part numbers are for comparison purposes only. All prices are in €, excl. VAT. Errors reserved. Delivery subject to availability.